Starting the Engine

  1. Make sure the parking brake is applied.
    • The parking brake and brake system indicator (red) comes on for 30 seconds when you pull up the electric parking brake switch.
Continuously variable transmission models
  1. Check that the transmission is in P, then depress the brake pedal.
    • Although it is possible to start the vehicle in N, it is safer to start it in P.
Manual transmission models
  1. Check that the shift lever is in P. Then depress the brake pedal with your right foot, and the clutch pedal with your left foot.
    • The clutch pedal must be fully depressed to start the engine.
All models
  1. Press the ENGINE START/STOP button without depressing the accelerator pedal.
Detail
Keep your foot firmly on the brake pedal when starting the engine.

The engine is harder to start in cold weather and in thinner air found at altitudes above 8,000 feet (2,400 meters).

When starting the engine in cold weather, turn off all electrical accessories such as the lights, climate control system, and rear defogger in order to reduce battery drain.

If you live in a region where winter is extremely cold, an engine block heater will improve starting and warming of the engine. Consult a dealer for details.

If the exhaust system sounds abnormal or you can smell exhaust gas inside the vehicle, have your vehicle checked by a dealer. There may be a problem with the engine or exhaust system.

Bring the keyless remote close to the ENGINE START/STOP button if the battery in the keyless remote is weak.

The engine may not start if the keyless remote is subjected to strong radio waves.

Do not hold the ENGINE START/STOP button to start the engine.
If the engine does not start, wait at least 30 seconds before starting the engine again.

The immobilizer system protects your vehicle from theft. If an improperly coded device is used, the engine’s fuel system is disabled.

Remote Engine Start*

You can remotely start the engine using the two-way keyless remote from extended distances.

WARNING

Carbon monoxide gas is toxic and can rapidly accumulate in closed or even partly enclosed areas.

Breathing it can cause unconsciousness and even kill you.

Never use the remote engine starter with the vehicle parked in a garage or other areas with limited ventilation.

Detail
The remote engine start may violate local laws.
Before using the remote engine start, check your local laws.

If there are buildings and obstacles between your vehicle and the keyless remote, the range will be reduced.
This distance may vary by external electrical interference.

The engine may not start by the remote engine start if:
  • You have disabled a remote engine start setting using the driver information interface.
    Models with 7-in. Color Touchscreen
    Models with 9-in. Color Touchscreen
  • The power mode is not in VEHICLE OFF.
  • The transmission is in a position other than P.
  • The hood is open, or any door or the hatch is unlocked.
  • You have already used the keyless remote twice to start the engine.
  • Another registered keyless remote is in the vehicle.
  • There is any antenna failure.
  • The door is unlocked with the built-in key.
  • The engine oil pressure is low.
  • The engine coolant temperature is extremely high.
  • The telematics unit* malfunctions.
  • The security system alarm is not set.
  • The 12-volt battery temp is too low or the 12-volt battery charge is too low.

Before starting the engine, make sure to check the door lock status using the keyless remote. When you press the button, wait for the green LED to blink. If the red LED turns on, the doors and hatch did not lock, and the engine does not start.

While the engine is running, the vehicle will automatically precondition inside the vehicle.
When it is warm outside:
  • The climate control system is activated in recirculation mode.
When it is cold outside:

To start the engine

Press the button, then press and hold the button.

  • Continues to blink during a vehicle self check until the engine starts.

Green LED: Comes on while the engine is running.

Red LED: Blinks when the keyless remote is out of the keyless system range.

  • Go within the range, and try again.

The engine runs for up to 10 minutes without you starting the vehicle.
To extend the run time for another 10 minutes during the first run, press the button, then press and hold the button.

  • The amber LED blinks, then the green LED comes back on if a 10-minute extension request was transmitted successfully.

After pressing the button, wait for the green LED to blink. This indicates that the all the doors and the hatch are locked.

To stop the engine

Press and hold the button for one second.

Red LED: Comes on for one second to let you know that the engine has stopped.

Red LED: Blinks when the keyless remote is out of the keyless system range.
The engine will not stop.

  • Go within the range, and try again.

Starting to Drive

Continuously variable transmission models
When the engine was started using the button on the keyless remote
  1. Depress and hold the brake pedal, then press the ENGINE START/STOP button.
When the engine was started in any case
  1. Keeping your right foot on the brake pedal, put the transmission into D. Select R when reversing.
  2. With the parking brake applied, release the brake pedal and gently depress the accelerator pedal.
    • Make sure the parking brake and brake system indicator (red) goes off.
Detail
Manual transmission models with Auto Idle Stop
Engine Restart Function
If the engine stalls, fully depress the clutch pedal within three seconds. The engine may automatically restart under certain conditions. Otherwise, follow the standard procedure.

Continuously variable transmission models
When the engine was started using the button on the keyless remote
The engine stops when the transmission is taken out of P before the ENGINE START/STOP button is pressed. Follow step 1 when starting to drive.

All models
You can also release the parking brake by pressing the electric parking brake switch while depressing the brake pedal.
When facing downhill, you can start your vehicle more smoothly by manually releasing it with the electric parking brake switch than by releasing it with the accelerator pedal.

Hill start assist system

Hill start assist keeps the brake engaged briefly to help prevent the vehicle from rolling on inclines as you move your foot from the brake pedal to the accelerator.

Continuously variable transmission models

Put the transmission into D or S when facing uphill, or R when facing downhill, then release the brake pedal.


Manual transmission models

Depress the clutch pedal, and shift to one of the forward gears when facing uphill, or R when facing downhill, then release the brake pedal.

Detail
Hill start assist may not prevent the vehicle from rolling downhill on a very steep or slippery slope, and will not operate on small inclines.

Hill start assist is not a replacement for the parking brake.

Hill start assist will operate even when VSA® is switched off.

Stopping the Engine

You can turn the engine off when the vehicle is completely stopped.

Continuously variable transmission models
  1. Put the transmission into P.
  2. Press the ENGINE START/STOP button.
Manual transmission models
  • If the transmission is in N, press the ENGINE START/STOP button.
  • If the transmission is in any gear other than N, depress the clutch pedal, then press the ENGINE START/STOP button.
Detail
The power mode will automatically turn to VEHICLE OFF about 20 minutes after the following conditions have been met:
  • A door has been opened, such as when leaving the vehicle.
  • The driver’s seat belt is not fastened.
    • Continuously variable transmission models
  • The transmission is in P.
    • Manual transmission models
  • The vehicle is completely stopped.

* Not available on all models

Recommended topic(s)